Home Products Adhesives and Primers EPDM Glue Roof Glue EPDM Upstand

Roof Glue EPDM Upstand

Contact adhesive for bonding EPDM membrane to upstands

A sprayable contact adhesive for bonding FlexiFoil EPDM vertically to roof upstands and horizontally to the roof surface (at least 15 cm from the upstand). The contact adhesive should be applied to the entire upstand, the first 15 cm of the roof surface, and the EPDM membrane to protect against the wind. This contact adhesive can be used both horizontally and vertically. It can be applied quickly and easily thanks to the handy spray can. This adhesive is not suitable for bonding seams or accessories.

  • Bonds EPDM to the roof surface and upstands
  • Can be used horizontally or vertically
  • Adheres to most substrates

Step-by-step plan

  1. Make the substrate dry, dust- and grease-free.
  2. Fold back the FlexiFoil EPDM foil 15 cm all around.
  3. Apply the contact adhesive using the spray can to the first 15 cm of your roof surface, the upstands and to the FlexiFoil EPDM sheet itself. Do not apply more adhesive than can be processed in 5-10 minutes.
  4. Wait until the adhesive is finger dry, carefully fold back the FlexiFoil EPDM film and press the film firmly. Make sure there are no folds or any form of air inclusion. When doing this, always work from the middle towards the sides. Then roll it on well with an EPDM roller. The use of this contact adhesive is 0.35L/m² applied on both sides.
  5. Finish the eaves further with an Aquaplan aluminium profile.

Calculate how much product you need

Step 1 of 2

  • cm
  • cm
  • cm
  • cm
  • cm
  • cm
  • cm
  • cm
  • cm
  • cm
* By using this calculation module, one agrees to the terms of use: All results are indicative and approximate only. Aquaplan can in no way be held responsible for deviating results resulting from the use of this calculation module.

Technical features

Dimensions 7 × 7 × 34,5 cm
Variation

Roof Glue EPDM Upstand 750 ml

EAN

5413466954667

Volume

0.75

Color

white

Content indication

L

Material

Polymer

Product use

Glue

Required tools

Pressure Roller

Minimum processing temperature

5

Maximum processing temperature

35

Dry time (in hours)

48

Repaintable

Not applicable

Repaintable after (hours)

Niet van toepassing

Suitable for part of building

Flat roofs

Safety features

H-phrases H222 - Extremely flammable aerosol.
H229 - Pressurized container: May burst if heated
H315 - Causes skin irritation.
H319 - Causes serious eye irritation.
H336 - May cause drowsiness or dizziness.
H410 - Very toxic to aquatic organisms, with long lasting effects.
P-phrases P210 - Keep away from heat/sparks/open flames/hot surfaces and other ignition sources. - Do not smoke.
P261 - Avoid breathing dust/fume/gas/mist/vapour/spray.
P273 - Avoid release into the environment.
P280 - Wear protective clothing.
P304 - AFTER INHALATION:
P312 - If you feel unwell, call a POISON CENTER/doctor/....
P305+P351+P338 - IF IN EYES: Rinse cautiously with water for several minutes. remove contact lenses, if possible; keep rinsing.
P403+P233 - Store in a well-ventilated place. Store in tightly closed container.
P501B - Dispose of contents/container in accordance with local regulations.
EUH-phrases None
Pictograms GHS02 - flame
GHS07 - exclamation mark
GHS09 - environment
UFI-code HXJ4-116D-5805-AY84
IMDG-code AEROSOLS