0
IKO enertherm Combi-Cover
PIR insulation with finishing layer in one convenient panel
IKO enertherm Combi-Cover panel has all the qualities of an IKO enertherm insulation board, plus a special finishing layer. This allows you to paint or wallpaper straight away. The PIR insulation board is bonded to a magnesium oxide board (3 mm) that has many positive properties: it’s sturdy, insensitive to moisture, fireproof and very light, which facilitates installation.
- Very sturdy, dimensionally stable and light
- Quicker installation thanks to unique click system and invisible fastenings
- Choice of finishing: paint or wallpaper
Step-by-step plan
- Before you start working, check the roof structure for defects. If a wall is not sufficiently straight or space is required for cabling, install a wooden slatted structure first. The COMBI-COVER can be installed over an existing slatted structure or between purlins. Always start at the bottom in a corner and work upwards. Ensure the insulation boards are mounted about 1.5 cm from the walls and adjoining materials.
- First screw the steel CLIP & FIX 1 SIDED bracket to the floor joist using the supplied screws. Ensure that the 2 prongs point upwards. Use approximately 3 CLIP & FIX 1 SIDED brackets per board. Gently push the insulation board, with the tongue up and groove down, onto the prongs of the CLIP & FIX 1 SIDED bracket. The next board will connect with the previous board thanks to the unique tongue-and-groove system.
- At the end of the first row, cut the insulation board to size. The leftover piece can be used as the first piece to start the second row. Now place steel CLIP & FIX 2 SIDED brackets on the top of the first row of insulation boards. Gently push the prong into the insulation material. Make sure the prong with holes is placed against a beam so that the CLIP & FIX 2 SIDED bracket can be secured with the supplied screws.
- The joints of the second row must be staggered. Carefully push the insulation boards onto the previously mounted CLIP & FIX 2 SIDED brackets. Make sure the underside of the insulation rests on the two prongs. Make sure the boards connect up with the underlying and adjacent boards. When this row is finished, just like for the first row, carefully push the prong of the IKO enertherm CLIP & FIX 2 SIDED bracket into the insulation material and screw it in place.
- Finish the wall, repeating these steps. The final row of insulation boards (at the top against the ridge beam) should be sawn to size in advance following the slant of the ridge beam. Leave a gap of 1.5 cm between the top row and the ridge beam. Take this into account when cutting the boards to size. Use approximately 3 CLIP & FIX 1 SIDED brackets per board. Screw them in place.
- Seal large gaps with the wall, floor and ceiling with IKO enertherm PUR foam ISO-FILL. Fill all seams and uneven areas with 1 or 2 coats of IKO enertherm COVER FINISH. Once the filler has dried, sand the wall and then finish as desired.
Calculate how much product you need
* By using this calculation module, one agrees to the terms of use: All results are indicative and approximate only. Aquaplan can in no way be held responsible for deviating results resulting from the use of this calculation module.
Accessories
Technical features
| Dimensions | 120 × 60 × 33,2 cm |
|---|---|
| Variation | IKO enertherm – 8cm (4pcs)IKO enertherm – 10cm (4pcs) |
| EAN | 54134669487655413466948772 |
| Rd-waarde (m²K/W) | 3.64.5 |
| Volume | 14 |
| Material | PIR (polyisocianuraat)PIR (polyisocianuraat) |
| Product use | InsulateInsulate |
| Thickness (mm) | 332412 |
| Width (mm) | 600600 |
| Surface area (m²) | 0.722.88 |
| Length (mm) | 12001200 |
| Lambda-value | 0.0220.022 |
| Connection type | Tongue and groove connectionTongue and groove connection |
| Attachment/application method | Clip systemClip system |
| Content indication | Stuk(s)Stuk(s) |
Related products
Onze cookies zijn waterdicht
Functioneel Always active
De technische opslag of toegang is strikt noodzakelijk voor het legitieme doel het gebruik mogelijk te maken van een specifieke dienst waarom de abonnee of gebruiker uitdrukkelijk heeft gevraagd, of met als enig doel de uitvoering van de transmissie van een communicatie over een elektronisch communicatienetwerk.
Voorkeuren
De technische opslag of toegang is noodzakelijk voor het legitieme doel voorkeuren op te slaan die niet door de abonnee of gebruiker zijn aangevraagd.
Statistieken
De technische opslag of toegang die uitsluitend voor statistische doeleinden wordt gebruikt.
De technische opslag of toegang die uitsluitend wordt gebruikt voor anonieme statistische doeleinden. Zonder dagvaarding, vrijwillige naleving door uw Internet Service Provider, of aanvullende gegevens van een derde partij, kan informatie die alleen voor dit doel wordt opgeslagen of opgehaald gewoonlijk niet worden gebruikt om je te identificeren.
Marketing
De technische opslag of toegang is nodig om gebruikersprofielen op te stellen voor het verzenden van reclame, of om de gebruiker op een website of over verschillende websites te volgen voor soortgelijke marketingdoeleinden.